Custom Flexible Film Target

CUSTOM MADE Film Photo Tool

In stock
US $0.00

Maximum 200 characters

Maximum 500 characters


We can source lots of different materials, with specialised coatings and manufactured to different shapes, sizes and thickness. Please select the options that you require from the fields above, and give us plenty of NOTES where possible.

Note that we only hold a small amount of specialised material in stock, but can order custom materials on request. There may be a slightly longer delay, or minimum order quantities for some material combinations. If possible, select "ANY AVAILABLE" from the drop down lists where available so that we can try to match your requirements to stock that we currently hold, thereby reducing delays and costs.



We can write masks at 4 different resolutions, called "classes". The higher the resolution, the better the qualtity. Please see the section SPECIFICATIONS to see the impact that class resolution has on dimensional accuracy and feature tolerances.

Class 1 :   This represents a resolution that is equivalent to approximately 64k dpi (previously known as High Resolution). Although this resolution may resolve smaller features, we recommend keeping feature sizes above 10um as corner rounding is considerable. Edge sharpness and definition is acceptable for non critical design types, although designs with arcs/circles and lines running off 90 degree grid may show pixilation. NO features such as lines / circles / spots / squares below 10 um unless on a 'best effort' basis previously agreed with our technicians.    

Class 2 :   This represents a resolution that is equivalent to 128k dpi (previously known as Super High Resolution). This resolution will resolve down to 4 micron lines and has good line edge qualities with only a small pixilation along edges. Corner rounding is below 3um but still visible. NO features such as lines / circles / spots / squares below 4um unless on a 'best effort' basis previously agreed with our technicians.  

Class 3 :   This represents our most common resolution for demanding, high precision photomasks. It is equivalent to 256k dpi , and offers an excellent price / quality balance. This resolution will resolve down to 2 micron lines and has very good  line edge qualities with no pixilation along edges, and corner rounding is kept to a minimum.

Class 4 :   This represents our highest resolution, which is equivalent to 512k dpi  (a brand new offering !) , and is the best quality that we can offer. Only available upto 7.6" / 200mm image area. This resolution will resolve down to 1 micron lines and has excellent line edge qualities with no pixilation along edges, and corner rounding is barely visible.


Data formats listed above are only a small section of what is available. If your chosen format is not listed, please contact us for further information and clarification. We are also able to provide a full drafting service whereby we can create your designs from drawings and descriptions.

Film Photomask Polarity POLARITY

Masks are normally referred to as Clearfield (positive) &  Darkfield (negative)

Positive means that the data you have drawn in CAD will be Chrome on the mask, with the background (the field) being clear glass.

Negative is the opposite of this, where the items drawn on CAD will be clear and the background will be chrome. 

We also need to know which way round the mask has been designed on your screen. The easiest way to select this is to add some reference text (anything you like) to the design somewhere - maybe in the corner - and then specify if the text needs to be right reading or wrong reading.



Our standard production turnaround is 4 days from receipt of the artwork, purchase order and related documents. We can offer faster services if required for more urgent orders.


Standard :   We firstly inspect the piece by eye for flaws, design inaccuracies and contaminations. We also inspect a test coupon (placed in the bottom corner of the mask) for line width accuracy and edge definition. Next we measure the overall dimension of the mask, and record both of these measurements on our internal inspection records. Finally, we find the CD of the mask, measure that, record it, and also take a digital photo that is saved with the inspection log. We use Nikon MM40 at 900x magnification and an OGP ZIP 300 at 400 x magnifications for this.

Certificate of Conformance:   In addition to the standard inspection process described above, we will also supply a printed Certificate of Conformance.

Certificate of Measurement :   By selecting this option during the ordering process, we will inspect upto 10 customer defined measurements, with customer supplied tolerances. You will need to send us a document, or a separate layer of the design, showing us where you want us to take the measurements from. There can be upto 10 positions defined by the customer. These dimensions are then programmed on the co-ordinate measuring system and the mask is compared to this unique program. A certificate of measurement /conformity is given if the mask passes the inspection process. Additional positions can be requested if required.



A method of sending an email copy of the design for verification before the mask is written. The ‘PDF Checkplot” is a low resolution (4000 dpi) graphic representation of the final photomask - the quality of the PDF does not represent the quality of the final photomask, it is a "gross overview". You must approve this by email before we can proceed.  

For more accurate checkplot representation , it is best to send you a detailed  CAD checkplot which will represent the design perfectly – in high resolution – and gives you the ability to also measure. You do not need to install any special software, we will give you the link to our online CAD viewer at the time of the checkplot.



Please let us know the CAD file name / number so that we can tie together the uploaded data and the order.



Here you can inform us of any other requirements or specifications regarding the order.


Please see the TECHNICAL sections, DOWNLOAD sections and FAQ for further information. If you still require clarification, pleas either email or click for LIVE SUPPORT.


There are two different values that we specify for tolerances. The first is a ‘feature tolerance’, which equates to one specific feature (also known as CD or Critical Dimension). So, if part of your mask design has a 12um channel and this is a critical feature, you can use the table below to work out possible deviations to the channel width, depending upon which resolution you choose. As a rule, the higher the resolution, then the more accurate the individual feature size will be.







16k dpi on polyester film

4.8um + 10% host
Max 9.6um


32k dpi on polyester film

2.4um + 10% host
Max 4.8um


64k dpi on polyester film

1.2um + 10% host
Max 2.4um


128k dpi on polyester film

0.6um + 10% host
Max 1.2um

                                All figures above in Microns....
                                Example, at grade 3 resolution a 10um line would have a tolerance of (1.2 + 0.1) = 1.3



The second tolerance that customers ask us about is that of overall dimensional tolerances. These refer to the tolerances over a distance greater then 5mm – in layman’s terms, people ask us ‘how accurate will the mask be’ and these guidelines should go somewhere towards providing the tolerances in overall dimensions ,depending upon the resolution chosen. Again, it goes without saying that the higher the resolution, then the more accurate the final mask.

Our photo-mask films are produced in conditions of 21deg C / 50% humidity, and if dimensional accuracy is a concern when using the polyester mask, then you must replicate these conditions in your own clean rooms and acclimatise the mask in these conditions for upto 8 hours before you intend to use it – only then can it be considered to be dimensionally accurate and stable. We strongly recommend using glass based substrates where dimensional stability is a concern.


When using films in your own production environemnt, be aware that ....
1 Deg C temperature change = 18 ppm (1.8um per metre length)
1% Humidity change  = 9ppm (0.9um per metre)






where L is measuring length in MM and the resulting
figure is in microns.


High Resolutions
GRADE 1 - 4

= 10.0um + (Lmm * 0.005) um 

Low Resolutions
4k / 10k

= 20.0um + (Lmm * 0.010) um

                                All figures above in Microns.... 
                                Example, at Grade 3 resolution a 100mm line would have a tolerance of (10.0 + 0.5) = +/- 10.5um
                                Our imaging process is accurate to +/- 5um, the remainder of the tolerance is due to environmental controls.



Polyester Film is a typical substrate used in the photographic process, and forms the most common substrate in applications that involve general multiple exposures (such as PCBs, etching, printing etc.). Polyester is excellent due to its low-cost nature, but must be handled carefully and used in controlled environments if dimensional accuracy is required.

Films used for photo-masks have the following component layers:  a plastic base, a photosensitive emulsion layer (silver halide) and a backing layer.

This plastic base is polyester material, and has a thickness of 0.18 mm. The emulsion layer is composed of gelatine and silver halide and other chemicals, which adds another 0.005mm in total.

When we expose the film in the imager, the light energy from the laser interacts with the silver halide crystals suspended in the coated gelatine layers. Development, a chemical process, converts exposed silver halide grains into metallic silver. The next step in the chemical process is fixation. The fixer stops development and removes the unexposed silver halide grains in non-image areas. Finally, the film is washed/dried/cleaned and inspected.

The final result is a ‘black’ image coated on one side of the polyester base. The density of the film is very high, typically Dlog of 4.5 – 5, giving it an excellent opacity to all common light sources.

Two concerns with emulsion film over glass are stability and robustness. Both the polyester and the gelatine absorb moisture and heat from their surroundings, and as such they undergo dimensional changes – quite considerably for some large area films. The other problem with the Gelatine/Emulsion is that it is relatively soft and must be handled carefully to avoid damage and scratches.


polyester film transmission


polyester specifications




Q: What is the smallest feature that you can do ? 
A: This depends upon the resolution that we image at, the material that we use, the tone of the mask, and most importantly the feature type (Spot, square, line etc). This all makes it very hard to give a figure, but as a very rough guide we can make 2-3um on an "everyday" basis and down to 1um and possibly below if we "hold it's hand through production" .

Q: How accurate are the features, what tolerances do you work to ? 
A: This is dependant upon the resolution that we image the mask at. The QUICK REFERENCE brochure in the DOWNLOADS section will give you a chart, specifying both feature and dimensional tolerances.

Q: What resolution should i pick ? 
A: The higher the resolution, then the sharper the edges of the features, the smaller the features possible, the more accurate the features will be, the sharper the corners in of the features, and also the smoother the circles. Some customers will notice this difference straight away, some will hardly notice any difference. Every customer has different requirements and different priorities. If in doubt, chose a higher resolution to ensure your requirements are met, but we are happy to advise if you send us your database.

Q: What does the term POLARITY  mean ?
A: Polarity is the tone of the photomask, and in layman's terms it is what you might call Positive and Negative. When you draw your photomask design on your computer, you need to decide if the objects that you draw are going to be opaque on the photomask- and therefore to block the light - or transparent areas on the photomask. It's best to always think of the data that you draw either being positive data, or negative data.  If used in contact lithography, remember, this is polarity or tone of the mask that we manufacture, and NOT the polarity of the wafer you are using. 

Q: I've designed my mask with the wrong polarity - what do i do ? 
A: We can use the original design file and simply reverse the tone of the mask. This is much easier than supplying new data.

Q: What is Right Reading, Wrong Reading and Mirrored.
A: Some people use the photomask in contact exposure, and others use it as an optical component. Making sure that the design is the corect way round is important. To inform us exactly what you need, it is best to add a title or reference text somewhere on the design and then we can talk in terms of "right reading" or "wrong reading ". Another way of thinking about "wrong reading" is to think of the text being mirrored. Right Reading Chrome side Down is the most common way to describe a photomask that will be used for contact lithography. When you hold the mask in your hands with the chrome side facing down closest to the wafer, the image on the mask will be correct or how it should appear on the wafer. Right Reading Chrome Up is maybe the most common way to describe optical components. However, every customer has different requirements from the next, so you need to inform us via the order form.

Q: So what would Negative Data - Right Reading Chrome Down actualy mean ? 
A: Using the above Q&A's as a reference, we can now say that when you are holding the photomask plate in your hand, and the text is reading correctly, then the chrome will be on the underneath surface and the glass support is uppermost. The design will be an exact opposite - in tone - of what you had designed on the computer.